2n EasyGate - User Manual Instrukcja Użytkownika Strona 1

5A transistor switch or logic signal can be used too. The pin near the telephone line connector is connected to GND of the device the second one is

63. EasyGate Status Indication 3.1. Indication LEDs Name Meaning Power supply · Light = EasyGate is powered. · Flashes once in 2s = HW error,

7§ The called number has too many digits (more than 30). § The called number is barred. § The called subscriber line is busy. § The called subsc

84. SIM Card PIN protection If a SIM card is PIN-protected and the PIN is not programmed in EasyGate, GSM LED indicates the state and the PIN tone i

95. Voice function Outgoing and incoming call establishing procedures for an analog telephone are described for illustration. The procedures are the

105.3. FAX call (only on models with fax converter) EasyGate with fax converter has ability to send and receive fax messages using analog fax Group

116. SMS Sending Input This universal input is intended especially for reporting alarm or error statuses of any equipment provided with the appropri

127. COM – Serial Interface The complete serial interface RS-232C on a 9-pin connector is identical with any external modem. The transmission rate r

137.3. FAX Transmission - PC-FAX EasyGate allows fax transmissions from your PC. However, do not confuse the PC-Fax service with a standard fax serv

147.6. Combination of COM Traffic with Voice Calls As already mentioned, SMS transmission can be made even during telephone calls. The SMS program i

Dear customer, Let us congratulate you on having purchased the EasyGate system. This new product has been developed and manufactured to provide the

158. EasyGate Parameter Programming All EasyGate parameters have such default values that meet most users’ demands and need not be changed. To chang

168.2. PC based Programming For programming, connect EasyGate to a PC with a serial cable and make sure that the EasyGate PCManager is installed. Pr

178.2.2. Further Data Handling Options In addition to the EasyGate memory, settings can be saved in a PC file and reloaded into the PCManager. This

18· The GSM provider's name and signal strength received by EasyGate - this information helps you find the optimum signal location (the inform

198.3. Parameter Tables All programmable parameters are listed in this section. Each parameter is accompanied with the unit used, function number (i

20Beep after dialing end Function No.: - Select a beep to signal the end of dialing (beginning of outgoing call establishing). Setting options

21 Line reversal indication for call in progress Function No.: - Select call in progress signaling by telephone line polarity reversal. There is v

228.3.2. Routing Parameters All parameters related to the number dialed for an outgoing call are arranged in this table. According to the prefix you

23Routing table enable Function No.: 20 Enable the use of the routing table with this parameter. Disabling this parameter you put the table out

24Extra tariff Function No.: - Pseudo tariff metering setting (tariff is based on call duration). The Extra tariff parameter defines transmi

User Manual Versions Version Amendments to Earlier Versions 1.00 · The User Manual applies to EasyGate FW Version 1.00D. 1.01 · New parameter for d

258.3.4. GSM & SIM Parameters GSM operator lock Function No.: - Provider blocking is set by manufacturer in EasyGate. If EasyGate is blo

26Serial number Function No.: - EasyGate serial number - for information only (cannot be changed). Must be used for communication with the man

278.3.7. Security Parameters PIN - value Function No.: 40 Fill in the PIN value for automatic PIN entering upon EasyGate power up. It is a

289. Troubleshooting No LED is on after power up · Check the power supply. All LEDs are on. No call is currently in progress. · EasyGate is in th

2910. List of Abbreviations · APN - Access Point Name – necessary for the GPRS service · CLIP - Calling Line Identification Presentation · CSD

3011. Technical Parameters GSM: GSM module, GSM bandwidth MC39i EGSM 900 / GSM 1800 MC55 EGSM 900 / GSM 1800 / GSM 1900 MC56 EGSM 850 / GSM 1

31 © 2006, 2N TELEKOMUNIKACE a.s.

Packing List An EasyGate delivery contains the following items: Item Number of Pieces EasyGate 1 pc Antenna for direct connection 1 pc 1) Magneti

CONTENTS 1. EASYGATE PURPOSE...1 1.1. BASIC F

1 1. EasyGate purpose 1.1. Basic Functions · The primary purpose of EasyGate is to transmit voice between a GSM network and an attached FXO-interfa

22. Installation 2.1. Proper Location · EasyGate is designed for vertical mounting on suspension holes (use the mounting pattern). This position is

32.2. External Antenna Connection Screw the antenna enclosed into the SMA antenna connector. Tighten the antenna connector gently with your hand - n

42.4. Connector description SMS sending input Telephone line RJ 12, 6/2 Power supply connector DC Jack 2,1mm RS232C serial line D-Sub 9 pins 2.